Comments on: CyanogenMod 4.1.99

By: Treadmill

Treadmill — Wed, 08 Dec 2010 17:17:55 +0000

I really treasure your work , Great post.

By: Carlos

Carlos — Fri, 27 Nov 2009 17:09:00 +0000

I don’t know how can I use the keyboard console.
The screen shows press enter… but, where is the keyboard?

By: DJC

DJC — Tue, 17 Nov 2009 10:16:55 +0000

I have the same problem with my HTC Magic (aka MyTouch) … When select the console I get “” and cannot access a keyboard.. in fact the only way out seems to be a remove-battery power off!!

By: Jacob

Jacob — Sat, 07 Nov 2009 02:02:51 +0000

Hi, I’ve installed the most recent ROM on my MyTouch, however when I boot to safe mode and attempt to use the console to partition my sd card, I cannot use the console. I click “go to console” but then I get stuck, as the MyTouch has no built-in keyboard, so I can’t hit “enter/return”. I can’t pull up a keyboard by holding down menu either. Any idea what’s going on or how I could use console? thanks!

By: Nicolas Jordan

Nicolas Jordan — Thu, 05 Nov 2009 18:00:10 +0000

Hey is this only going to work with specific G1′s cause its not working with me

By: CWJuhl

CWJuhl — Tue, 13 Oct 2009 17:22:34 +0000

I have my G1 rooted and using the Jesusfreke 1.5 rom image. How would I install the Cyanogen Rom image?

By: Tony

Tony — Sun, 11 Oct 2009 21:45:05 +0000

Hey Dryale – what’d you do to get bluetooth pairing to work? Still not working for me in 4.1.999 Hopefully Canyogen fixes this in 4.2

By: Charles

Charles — Sat, 10 Oct 2009 05:44:00 +0000

I upgraded two g1’s to 4.1.99 and then to 4.1.999. First they were slow. I had to upgrade my ext2 partition to ext3. I did this from cyanogen recovery console, 4.1 Go to console, enter/return, on the keyboard and typed the command, upgrade_fs next to the # and then pressed enter.
First make sure you have recovery console 4.1 installed. Use this, in the instructions for installing it from the terminal emulator make sure you type, su then press the return/enter then type in the flash command per the instruction.
http://www.cyanogenmod.com/downloads/recovery-image
Then you must be in the 4.1 recovery console, you access by holding down the power and home buttons while rebooting, got to alt-x Go to console)
in console press enter/return
enter the command upgrade_fs then press enter/return then type reboot and press enter.
I then downlaoded everything I needed and put them on my sd card and installed following these instructions.
http://www.simplehelp.net/2009/10/04/how-to-install-cyanogenmod-4-1-99-on-your-g1-android-phone/
Worked like a charm and runs fast. Hope this helps.

By: Charles

Charles — Sat, 10 Oct 2009 02:28:57 +0000

I upgraded two g1′s to 4.1.99 and then to 4.1.999. First they were slow. I had to upgrade my ext2 partition to ext3. I did this from cyanogen recovery console, 4.1 Go to console, enter/return, on the keyboard and typed the command, upgrade_fs next to the # and then pressed enter.
First make sure you have recovery console 4.1 installed. Use this, in the instructions for installing it from the terminal emulator make sure you type, su then press the return/enter then type in the flash command per the instruction.
http://www.cyanogenmod.com/downloads/recovery-image
Then you must be in the 4.1 recovery console, you access by holding down the power and home buttons while rebooting, got to alt-x Go to console)
in console press enter/return
enter the command upgrade_fs then press enter/return then type reboot and press enter.
I then downlaoded everything I needed and put them on my sd card and installed following these instructions.
http://www.simplehelp.net/2009/10/04/how-to-install-cyanogenmod-4-1-99-on-your-g1-android-phone/
Worked like a charm and runs fast. Hope this helps.

By: Tony

Tony — Fri, 09 Oct 2009 21:30:39 +0000

Hmm…I have 4.1.999 installed and my bluetooth unit still will not be discovered, let alone paired! Don’t know what’s up? Worked fine with 4.0.4…do I need to hard reset?